Yamato SM520 Instruction Manual Download Page 88

Page: 88 / 111

5. Handling Precautions

Warning

If a problem occurs

If smoke or strange odor should come out of this unit for some reason, turn off the power key

right away, and then turn off the circuit breaker and the main power. Immediately contact a

service technician for inspection. If this procedure is not followed, fire or electrical shock may

result. Never perform repair work yourself, since it is dangerous and not recommended.

Measure for flammability and handling of flammable solvent

This unit is not designed as the explosion-proof construction. Pay special attention to the

handling of the sample to be handled with this unit on the consumption with the explosive

material, flammable material, and similar ones. The flammable material may be vaporized by

leaving it at the temperature higher than room temperature, and could cause the fire or

explosion. When handling such material, provide ventilation with enough before the operation.

Keep the unit well-ventilated

Keep the heat releasing outlets in the side and back of the unit open during operation. If

they are closed, the inside temperature of the unit may increase, its performance may

deteriorate, or an accident, malfunction or fire may result.

Exercise care not to allow a liquid to get on the unit

Exercise care not to allow a liquid to get on the unit or enter the unit through the heat

releasing outlets in the side or back of the unit. If it enters the unit, immediately stop the

operation. Otherwise. an accident, malfunction, electric shock or fire may result.

Do not drop metallic pieces into the unit

Do not drop metallic pieces, such as clips, staples and screws, into the unit. If such a metallic

piece has dropped into the unit, turn it off. An accident, malfunction, electric shock or fire may

result.

Do not open the panels and covers

Do not operate the unit with the fixed panels and covers open. An accident, malfunction or

electric shock may result.

Do not modify

Do not modify this unit. An accident, malfunction, electric shock or fire may result.

Summary of Contents for SM520
















































































































Search results

Summary of Contents for SM520

Reviews:

Yamato SM520, Instruction Manual, Page: 88 / 111

Search results

Summary of Contents for SM520

Reviews: