CUSTOMIZING YOUR BINDER 120
5-4
XEROX DOCUMENT BINDER 120 OPERATOR MANUAL
Changing the Customer Tools features
The table below contains the steps for changing each of the
Customer Tools features.
Customer Tools feature
What to do
Energy Saver
1.
Enter the Customer Tools mode as instructed in the previous section of this
chapter.
2.
Press the
Manual Start
button to select
Energy Saver
from the second line
of the Cover Supply Contents Display.
NOTE:
Energy Saver is the default selection each time you enter the
Customer Tools mode.
3.
Press the
New Job
button until the desired Hours setting is displayed.
NOTE:
You can select from 0 to 12. As you press the New Job button, the
hours increment by one until you reach 12. The cycle then begins again at 0.
NOTE:
If 0 hours and 0 minutes are selected, the timed Energy Saver mode is
disabled.
4.
Press the
Manual Start
button until the desired Minutes setting is displayed.
NOTE:
You can select 0, 15, 30 or 45. As you press the Manual Start button,
the minutes increment by 15 until you reach 45. The cycle then begins again
at 0.
5.
Press the
Stop
button to save the settings and exit the
Energy Saver
feature.
6.
Do one of the following:
•
Press the
New Job
button until the next feature you want to change
appears on the second line of the Cover Supply Contents Display.
•
Press the
Reset
button to exit the Customer Tools features.
Spine Width Units Display
1.
Enter the Customer Tools mode as instructed in the previous section of this
chapter.
2.
Press the
New Job
button until
Units
appears on the second line of the Cover
Supply Contents Display.
3.
Press the
Manual Start
button to select Units.
4.
Press the
Manual Start
button to display the desired Units measurement.
NOTE:
You can select “inch” or “metric.” As you press the Manual Start
button, you will switch between the two choices.
5.
Press the
Stop
button to save the setting and exit the Units feature.
6.
Do one of the following:
•
Press the
New Job
button until the next feature you want to change
appears on the second line of the Cover Supply Contents Display.
•
Press the
Reset
button to exit the Customer Tools features.
Summary of Contents for Document Binder 120
