Configuration
en
Installation and operating instructions Wilo DD-I
143
–
Level
Recording the current fill level to record data. Basis for the "Increasing" and
"Dropping" level functions at the digital output.
–
Pressure
Recording the current system pressure to record data.
–
Flow
Recording the current flow rate to record data.
ƒ
Input 53 Type/Input 54 Type
Also adjust the signal type (voltage (U) or current (I)) in the hardware at the fre-
quency converter. Observe the frequency converter installation and operating in-
structions!
Factory setting: 4...20 mA
Input:
–
0...20 mA
–
4...20 mA
–
0...10 V
ƒ
Input 53 Scale Max/Input 54 Scale Max
Factory setting: 1
Input: Maximum value as real numerical value with unit. The units for the control val-
ues are:
- Level = m
- Pressure = bar
- Flow = l/s
Separator for decimal places: Point
6.5.6.6
Relay Outputs
Assignment of the available functions to the relevant outputs. Designation of the out-
put terminals matches the designation at frequency converter Wilo-EFC.
The following outputs can be configured:
ƒ
Relay 1 Function
ƒ
Relay 2 Function
NOTICE! The assignment must match the hardware assignment at the frequency
converter!
ƒ
Relay 1 Function/Relay 2 Function
Factory setting: Not In Use
Input:
–
Run
Individual run signal of the pump
–
Rising Level
Message for increasing level.
–
Falling Level
Message for dropping level.
–
Error
Individual fault signal of the pump: Alarm.
–
Warning
Individual fault signal of the pump: Warning.
–
Cleaning
Message when the cleaning sequence of the pump is started.
ƒ
Relay 1 Invert/Relay 2 Invert
Output functionality: normal or inverted.
Factory setting: Off (normal)
6.5.6.7
Analog Outputs
Assignment of the available functions to the relevant outputs. Designation of the out-
put terminals matches the designation at frequency converter Wilo-EFC.
The following outputs can be configured:
ƒ
Output 42 Function
NOTICE! The assignment must match the hardware assignment at the frequency
converter!
ƒ
Output 42 Function
Summary of Contents for DD-I
