W&H Lara RIL-117 Instructions For Use Manual Download Page 83

Page: 83 / 138

Maintenance

800-cycle or biannual maintenance

SEQUENCE OF PROCEDURES TO CLEAN THE WATER TANKS

To clean the water tanks, proceed as follows:

1. "Prepare the sterilizer for cleaning the water tanks" below.
2. "Access to the water tanks" on the next page.
3. "Clean the water tanks" on page 86

PREPARE THE STERILIZER FOR CLEANING THE WATER TANKS

Proceed as follows:

Switch OFF the sterilizer and disconnect the mains cable.

Completely drain both water tanks (see "Draining the used and clean water tank"
on page 92).

To drain the detergent solution during the subsequent cleaning, leave the drain
tube attached to the drain port of the tank you want to clean.

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands