W&H Lara RIL-117 Instructions For Use Manual Download Page 119

Page: 119 / 138

119

Technical data

Usable space *

LARA 17: 11.5 l/W: 195 mm/H: 195 mm/D: 297 mm (3 gal/W:
7.7’’/H: 7.7’’/D: 11.7’’)

LARA 22: 15 l/W: 195 mm/H: 195 mm/D: 390 mm (4 gal/W:
7.7’’/H: 7.7’’/D: 15.4’’)

Bacteriological filter

0.3 µm

Note*: Usable space with standard rack and trays. With optional tracks and
trays, see "Accessories, spare parts, consumables" on page 123.

STEAM GENERATOR

Pressure safety valve

5 bar (72.51 psig)

Safety thermostats

230 °C (446 °F)

DISTILLED OR DEMINERALIZED WATER

Water quality

Fulfilling EN 13060 Ann. C (conductivity < 15μS/cm)

Average water consumption

0.13 to 0.59 litres/cycle (0.03 to 0.16 gal/cycle)

Tank volume

Clean water 4.9 l (1.29 gal), with air gap: 2.8 l, (0.74 gal)

Used water 4.8 l (1.27 gal)

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands