W&H Lara RIL-117 Instructions For Use Manual Download Page 51

Page: 51 / 138

Sterilizer tests

Open the chamber door, extract the tray using the tray holder and take the tube.

CAUTION! Risk of burns. The test pack is very hot at the end of the cycle.
Wear appropriate PPE (e.g. gloves).

Unscrew the tube capsule and remove the indicator strip.

Check the change in colour. See "Interpret the test result" below

INTERPRET THE TEST RESULT

Indicator

What happened

Test
passed

What to do next

The indicator strip has turned dark. The air was completely removed from
the capsule.

Yes

Part of the chemical indicator strip has not turned dark. The air removal
from the capsule was not complete.

Repeat the test. If it fails repeatedly,
call technical service.

WHAT TO DO NEXT

Compile the Helix test documentation form to trace the effectiveness of the sterilization cycle during the whole lifespan of your sterilizer. See
"Helix test documentation form" on page 134.

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands