W&H Lara RIL-117 Instructions For Use Manual Download Page 46

Page: 46 / 138

Sterilizer tests

PURPOSE OF THE TEST

The test is used to validate the sterilizer performance for textile load sterilization.

DESCRIPTION

It consists of several sheets of paper wrapped in a small packet with a chemical heat-sensitive indicator sheet in the middle. The colour
assumed by this indicator sheet at the end of the sterilization cycle gives the result of the test.

CARRY OUT THE TEST (IN ACCORDANCE WITH EN13060)

Empty the sterilizer chamber to ensure no load is present. Do not remove the
standard chamber accessories mounted (e.g. chamber rack and trays).

Place the Bowie and Dick test pack in the center of a tray in the lowest rack
position and close the chamber door.

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands