W&H Lara RIL-117 Instructions For Use Manual Download Page 64

Page: 64 / 138

Sterilization cycles

Tap

to abort the stop command.

The cycle continues programmed.

Tap

to abort the cycle: the

sterilizer starts a reset phase.

Notice: Do not switch off the sterilizer
during the reset phase: it takes some
time to reset the system and reach
safe conditions in the sterilizer
chamber.

Check the message. See
"Messages of a stopped
sterilization cycle" on the next
page.

Tap

to view the cycle

parameters. See "View the cycle
parameters" on page 62.

Open the chamber door.

Reprocess the load if necessary.

CAUTION! Hot steam. Wait
the steam to dissipate
before opening the door.

Note: Water could be present in the
chamber when opening the door. To
prevent spilling place a towel below the
chamber door.

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands