W&H Lara RIL-117 Instructions For Use Manual Download Page 24

Page: 24 / 138

Getting started

MAIN MENU FUNCTIONS

Icon

Label

Function

Opens the menu.

Settings

Sets the device.

Traceability

Opens the pages to monitor the performed cycle data and
manage users and printing.

Accessories

Opens the pages to select and calibrate the printers,
format the USB pen drive and activate special functions.

Maintenance

Carries out the maintenance procedure.

System Info

In general, shows the system information.

During a cycle, shows the cycle parameters in real
time.

SETTINGS MENU FUNCTIONS

Icon

Label

Function

Device

Opens the pages to set the device.

Icon

Label

Function

Language

Sets the language.

Date & Time

Sets time and date values and format.

Sterilizer
Name

Sets the sterilizer name.

Energy
management

Sets the standby mode.

Display

Sets the display brightness.

Cycle

Opens the pages to manage cycles.

Measurement
Units

Sets the unit of measure.

Connectivity

Opens the pages to manage the network connection.

WI-FI

Activates a communication protocol between the
sterilizer and an external gateway to extend connectivity
features.

Network
Status

Only with a network connection set. Provides information
about the network status.

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands