W&H Lara RIL-117 Instructions For Use Manual Download Page 118

Page: 118 / 138

118

Technical data

WATER SUPPLY SYSTEM (TO BE COMPLIANT WITH IEC61770)

Fitting

Backflow preventing device (IEC61770).

Temperature

max. 35 °C (95 °F)

Pressure

min. 2 bar – max. 8.6 bar (min 29 psi - max. 124.7 psi)

Flow

min. 0.25 – max. 0.5 l/min (min. 0.066 - max. 0.132 gal/min)

POWER SUPPLY SYSTEM

Nominal voltage and Max.
current

200–240 V ac, 50/60 Hz, 10 A, single-phase (refer to product
label)

Overvoltage category

Protection required

Suitable circuit breaker and a Ground Fault Circuit Interrupter (GFCI).
All protection devices must be certified according to applicable
standard. A grounded connection is essential.

Communication with other
devices

1 USB port in the front

1 USB port at the rear (optional)

Features

Fully micro-processor controlled, process evaluation system
according to EN13060.

Programmable standby mode.

Max. heat output

3000 kJ/h

INSTALLATION REQUIREMENTS

Working temperature

From +5 °C to +40 °C (from +41 °F to +104 °F)

Working relative humidity

Max. RH 80% up to 31 °C (88 °F), linearly decreasing to 50% at 40
°C (104 °F)

Storage temperature / rel.
humidity

From -20 °C to +60 °C (from -4 °F to +140 °F )/0–90 % (with empty
tanks)

Max altitude

3000 m asl

Min. atmospheric pressure

0.6 bar (8.7 psi)

Overall dimensions

W: 465 mm/H: 452 mm/D: 646 mm (W: 18’’/H: 17.8’’/D: 25.4’’)

Min. space required

W: 565 mm/H: 502 mm/D: 450 mm (W: 22.2’’/H: 19.8’’/D: 17.7’’)

Size of the door movement

W: 532 mm/H: 452 mm/D: 357 mm (W: 21’’/H: 17.8’’/D: 14’’)

Weight empty

LARA 17: 42.5 kg (93.7 lbs)

LARA 22:44 kg (97 lbs)

Max. weight (fully loaded)

LARA 17: 53.1 kg (117 lbs)

LARA 22: 56.1 kg (123.8 lbs)

Weight per support area

LARA 17: 36 kN/m

LARA 22: 37.65 kN/m

Enviroment pollution

Degree 2

STERILIZER CHAMBER

Pressure safety valve

2.6 bar (37.7 psig)

Safety thermostats

180 °C (356 °F)

Total volume

LARA 17: 17 l/Ø: 250 mm/D: 362 mm (4.5 gal, Ø: 9.8’’/D: 14’’)

LARA 22: 22 l/Ø: 250 mm/D: 440 mm (5.8 gal, Ø: 9.8’’/D: 17’’)

Summary of Contents for Lara RIL-117











































































































































Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands

W&H Lara RIL-117, Instructions For Use Manual

Search results

Summary of Contents for Lara RIL-117

Reviews:

Related manuals for Lara RIL-117

Brands by name

Popular brands