Volvo TAD650VE Workshop Manual Download Page 93

Page: 93 / 160

Group 30: Electrical system

Diagnostic Trouble Codes

FMI 5 Abnormally low current or open
circuit

Possible reason:

•

An open circuit in one or both of the cables to the
IEGR.

Suitable action:

Check cable harness and connectors between
EMS 2 and IEGR.

Check IEGR coil.

FMI 7 Mechanical fault

Possible reason:

•

IEGR solenoid mechanically stucked.

•

Too low oil pressure to activate the IEGR.

Suitable action:

Check function of IEGR solenoid.

Check engine oil pressure.

Measurements

NOTE!

If any of the measurements shows an abnor-

mal value, check the wiring to and from the engine in-
terface.

Checking the wiring:

NOTE!

Cut the current with the main switch.

Remove the connector to the IEGR solenoid.

Remove connector B from the EMS 2.

Connect the B connector to brakeout cable
9990014 with measurebox 9998699.

Use multimeter 9812519 to do a resistance mea-
surement.

Measurement points in box

Nominal value

30 (IEGR signal) -

≈

2 (IEGR connector)

57, 60 (relay +) -

≈

1 (IEGR connector)

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands