Volvo TAD650VE Workshop Manual Download Page 103

Page: 103 / 160

Group 30: Electrical system

Diagnostic Trouble Codes

101

Circuit description

The electronic injectors used on the engine has an
electronically controlled solenoid. The solenoid is con-
trolled by the engine control unit.

The injectors receive voltage from pin A59 orA 60 on
the engine control unit. To activate an injector solenoid
the engine control unit grounds the current injector.

Fault tracing

NOTE!

Identify which injector by the SID number.

FMI 3 Checking injector circuit

Conditions for fault code:

Injector activated and faulty voltage in injector low
side

Possible reason:

•

Short circuit to battery voltage on the pin on the
respective injector’s low voltage side. (EMS 2 pin:
56, 52, 48 and 44, 40, 36)

•

Short circuit between high voltage and low voltage
side.

•

Short circuit to battery voltage in low voltage in-
jector wire.

Suitable action:

Check cable harness and connectors between in-
jectors and engine control unit (EMS 2).

engine
interface

splice

Note! Only TAD 650, 660, 750, 760 has an engine interface. On
TAD 734 the wiring to the EMS 2 is the same but without any en-
gine interface.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands