Volvo TAD650VE Workshop Manual Download Page 98

Page: 98 / 160

Diagnostic Trouble Codes

Group 30: Electrical system

Fault tracing

NOTE!

If the control panel ONLY communicates on

the J1939 communication and NOT the redundancy of
J1587 for start, stop and throttle this fault code is ac-
tive in the VODIA and that is normal.

FMI 9

Fault condition:

“Time-out” on the J1587 bus.

Possible reason:

•

Fault in the communication with the DCU/CIU.

•

No DCU/CIU found.

•

Open circuit in the power supply cable between
the engine control unit and the DCU/CIU.

•

Faulty DCU/CIU.

Suitable action

Check communication cables to the DCU/CIU.

Check power supply cable between engine control
unit and DCU/CIU.

Check that DCU/CIU is programmed for correct
engine type.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands