manualshive.com logo in svg

Volvo TAD650VE, Workshop Manual, Page: 92 / 160

Share
Download
Volvo TAD650VE Workshop Manual Download Page 92

Diagnostic Trouble Codes

Group 30: Electrical system

90

Circuit description

Internal exhaust gas recirculation, IEGR, is like the
name says used for recirculation of exhaust gases.
This for lowering the emissions from the engine. The
IEGR valve is a 2-way solenoid valve controlled by
the engine control unit. The IEGR solenoid controls  a
oil pressure that effects a control valve which activate
the exhaust gas recirculation function. The solenoid is
activated when pin B30 on the EMS 2  changes its po-
tential.

Fault tracing

FMI 3  Abnormally high voltage or short
circuit to higher voltage

Possible reason:

•

Short circuited IEGR signal cable to 5V voltage or
to battery voltage.

Suitable action:

1.

Check cable harness and connectors between
EMS 2 and IEGR.

FMI 4  Abnormally low voltage or short
circuit to lower voltage

Possible reason:

•

Short circuited IEGR signal cable to battery nega-
tive.

Suitable action:

1.

Check cable harness and connectors between
EMS 2 and  IEGR.

engine
interface

Summary of Contents for TAD650VE

































































































































































Reviews:

No comments