Volvo TAD650VE Workshop Manual Download Page 91

Page: 91 / 160

Group 30: Electrical system

Diagnostic Trouble Codes

MID 128, PPID 19

Internal EGR status

MID 128: Engine control unit

FMI 3:

The voltage exceeds the normal value or is
short circuited to higher voltage.

FMI 4:

The voltage is less than the normal value or
is short circuited to battery negative.

FMI 5:

The current is less than the normal value or
is open circuited.

FMI 7:

Mechanical fault. The system responds in-
correctly.

FMI

Fault code explanation

3, 4, 5

Faulty sensor / Faulty sensor circuit

Mechanical fault

Fault indication

DCU:

Engine warning in DCU display.

CIU:

None

Flash code

Electrical fault: 8.5
Value fault:

None

Symptom

FMI 3, 4, 5:

IEGR can not be turned on.

FMI 7:

May damage turbine, increased
power and emissions.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands