Volvo TAD650VE Workshop Manual Download Page 71

Page: 71 / 160

Group 30: Electrical system

Diagnostic Trouble Codes

Measurements

NOTE!

If any of the measurements shows an abnor-

mal value, check the wiring to and from the engine in-
terface.

Signal cable:

•

NOTE!

Turn ignition off.

•

Disconnect the connector from the sensor.

•

Connect adapter cable 885675 to the cable har-
ness connector to the engine control unit.

•

Use multimeter 9812519 for voltage measure-
ment.

•

NOTE!

Turn ignition on.

Measurement points

Nominal value

1 – 2

≈

5 V

Negative cable:

•

NOTE!

Cut the current with the main switch.

•

Disconnect the connector from the sensor

•

Connect adapter cable 885675 to the cable har-
ness connector to the engine control unit.

•

Use multimeter 9812519 to do resistance mea-
surement against the engine control unit.

Measurement points

Nominal value

1 – Battery negative

≈

The point of connection for
battery negative on the en-
gine

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands