manualshive.com logo in svg

Volvo TAD650VE, Workshop Manual, Page: 47 / 160

Share
Download
Volvo TAD650VE Workshop Manual Download Page 47

Group 30: Electrical system

Diagnostic Trouble Codes

45

Measurements

Supply cable:

•

NOTE!

Turn ignition off.

•

Disconnect the connector from the monitor

•

Use multimeter 9812519 for voltage measurement

•

NOTE!

Turn ignition on.

Measurement points

Nominal value

Yellow conductor –

U 

≈

 Battery voltage x 0.8

Black conductor

Negative cable:

•

NOTE!

Cut the current with the main switch.

•

Disconnect the connector from the monitor

•

Use multimeter 9812519 to do resistance mea-
surement against the engine control unit.

Measurement points

Nominal value

Black conductor –

R 

≈

 0 

Ω

Battery negative

Checking water in fuel monitor

1.

Disconnect the connector to the water in fuel mon-
itor.

2.

Use multimeter 9812519 to do a resistance mea-
surement towards the monitor.

Measurement points

Nominal value

1 – 2 Monitor immersed

R 

≈

 0 

Ω

in water

1 – 2 Monitor immersed

R 

≈ ∞  Ω

in fuel

Summary of Contents for TAD650VE

































































































































































Reviews:

No comments