Volvo TAD650VE Workshop Manual Download Page 141

Page: 141 / 160

Group 30: Electrical system

Diagnostic Trouble Codes

139

FMI 7

Conditions for fault code:

Rail pressure release valve stuck close.

Possible reason:

•

An open circuit in one or both cables from EMS 2
to MPROP.

•

Short circuit to battery negative in MPROP posi-
tive wire, pin 1 on MPROP.

•

Rail pressure release valve stuck close.

Suitable action:

Check contact pressure in socket 12 and 16 in
engine connector A. Also check contact pressure
in connector at MPROP.

Check cable harness and connectors between
EMS 2 and MPROP.

Change the rail pressure release valve.

FMI 11

Conditions for fault code:

High rail pressure when rail pressure release valve is
open.

Possible reason:

•

Rail pressure controller out of range.

•

Pressure release valve stuck close or out of char-
acteristic.

Suitable action:

Check function of rail pressure sensor.

Change the rail pressure release valve.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands