Volvo TAD650VE Workshop Manual Download Page 42

Page: 42 / 160

Diagnostic Trouble Codes

Group 30: Electrical system

Measurements

NOTE!

If any of the measurements shows an abnor-

mal value, check the wiring to and from the engine in-
terface.

Supply cable

•

NOTE!

Turn ignition off.

•

Disconnect the connector from the sensor

•

Connect adapter cable 885675 to the cable har-
ness connector to the engine control unit.

•

Use multimeter 9812519 for voltage measure-
ment.

•

Turn ignition on.

Measurement points

Nominal value

1– 4

≈

Negative cable:

•

NOTE!

Cut the current with the main switch.

•

Disconnect the connector from the sensor

•

Connect adapter cable 885675 to the cable har-
ness connector to the engine control unit.

•

Use multimeter 9812519 to do resistance mea-
surement against the engine control unit.

Measurement points

Nominal value

4 – Battery negative

≈

The point of connec-
tion for battery nega-
tive on the engine

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands