Volvo TAD650VE Workshop Manual Download Page 60

Page: 60 / 160

Diagnostic Trouble Codes

Group 30: Electrical system

MID 128, PID 106

Boost pressure

MID 128: Engine control unit

FMI 0:

The sensor value is valid but above the nor-
mal working range.

FMI 3:

The voltage exceeds the normal value or is
short circuited to higher voltage.

FMI 5:

The current is less than the normal value or
is open circuited.

FMI

Fault code explanation

Boost pressure is too high

3, 5

Faulty sensor / Faulty sensor circuit

Fault indication

DCU:

Engine warning in DCU display.

CIU:

Flash code

Flash code

Electrical fault: 3.4

Value fault:

3.5

Symptom

FMI 0:

Power is reduced due to error torque map

if engine protection parameter is activat-
ed.

FMI 3, 5:

Pressure set to atmospheric pressure

+ 30 kPa. Engine performance is derated.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Volvo TAD650VE, Workshop Manual, Page: 60 / 160

Search results

Summary of Contents for TAD650VE

Reviews: