Volvo TAD650VE Workshop Manual Download Page 72

Page: 72 / 160

Diagnostic Trouble Codes

Group 30: Electrical system

Checking the sensor cable for an open circuit or
short-circuit:
NOTE!

Cut the current with the main switch.

•

Disconnect the connector from the sensor.

•

Connect adapter cable 885675 to the cable har-
ness connector to the engine control unit.

•

Remove connector B from the engine control unit.

•

Use multimeter 9812519 to do a resistance mea-
surement against the engine control unit connec-
tor B.

Measurement points

Nominal value

2 (885675)– 27 (EMS 2, conn.B)

≈

2 (885675)– 18 (EMS 2, conn.B)

≈ ∞ Ω

1 (885675)– 27 (EMS 2, conn.B)

≈ ∞ Ω

1 (885675)– 18 (EMS 2, conn.B)

≈

NOTE!

Measurement is done to eliminate short circuiting or

breaks in the cable to the engine control unit.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands