Volvo TAD650VE Workshop Manual Download Page 40

Page: 40 / 160

Diagnostic Trouble Codes

Group 30: Electrical system

Fault tracing

FMI 1 Fuel pressure is too low

Conditions for fault code:
The fuel pressure alarm depends on the engine revo-
lution.

Suitable action:

Check fuel level.

Open all fuel cocks and check that no leakage
occurs.

Check drive belt adjustment.

Change all fuel filters. (pre- and fine filter)

Check that no fuel hose is squeezed or folded.

Check function of fuel pressure sensor by control
measuring the fuel pressure. (see workshop man-
ual)

Check fuel feed pump.

Change fuel pressure release valve. (see work-
shop manual)

FMI 3 Abnormally high voltage or short
circuit to higher voltage

Conditions for fault code:

The voltage on pin B16 on the EMS 2 is more than
4,75 Volt.

Possible reason:

•

An open circuit in fuel sensor negative cable.

•

Short circuited fuel sensor signal cable to 5V volt-
age or to battery voltage.

•

Faulty sensor.

Suitable action:

Check contact pressure in socket 18 in the engine
connector B. Also check contact pressure in con-
nector at fuel pressure sensor.

Check cable harness and connectors between fuel
sensor and EMS 2.

Check function of fuel pressure sensor.

Summary of Contents for TAD650VE

































































































































































Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands

Volvo TAD650VE, Workshop Manual

Search results

Summary of Contents for TAD650VE

Reviews:

Related manuals for TAD650VE

Brands by name

Popular brands