Viking GB 460, Instruction Manual

Page: 60 / 656

0478 216 9905 A - EN 58
7.
1
Unpacking the garden
shredder
●
Open the packaging.
Installation position:
●
Remove the basic unit (A) from the
packaging with the help of a second
person and place it on the ground.
●
Remove the cardboard insert (1) and
place it on the ground. Remove the
wheels (F) and wheel carriers (B, C).
●
Place the cardboard insert (1) on the
ground with the closed side facing
upwards.
●
Lift the basic unit (A) with the help of a
second person and place it on the
cardboard insert as shown.
7.2 Attaching the chassis
1
Install right and left wheel carrier:
●
Raise the basic unit into the assembly
position. (
Ö
7.1)
Attaching the right wheel carrier:
●
Position right wheel carrier (B) on the
inside of angled support plate (1). The
bores in the wheel carrier must align
with the bores in the support plate.
●
Position a nut (J) on the inside. Insert
screw (I) through the bores (2) in the
support plate and in the wheel carrier
and screw into the nut (J) but do not
tighten.
●
Repeat this procedure at the second
bore in the right wheel carrier.
Attaching the left wheel carrier:
●
Hold the left wheel carrier (C) with the
bore (1) at the centre bore (2) on the left
side of the basic unit (A).
●
Screw in the screw (I) using the
installation tool (T), but do not tighten.
2
Install the foot and plug:
●
Push the foot (D) as far as possible
onto right wheel carrier (1) as shown.
The foot engages in the right wheel
carrier.
●
Repeat this procedure on the left wheel
carrier.
●
Carefully drive plug (E) into right wheel
carrier (2) as far as possible.
●
Repeat this procedure on the left wheel
carrier.
3
Mount the wheel on the axle:
●
Push the retaining ring (G) as far as
possible into the groove (1) in axle (H).
●
Push the wheel (F) onto the axle (H).
4
Install the axle and wheel:
●
Push the axle, with pre-installed
wheel (1) through the bores (2) in the
wheel carrier.
●
Push the left wheel (F) onto the
axle (1).
●
Push the retaining ring (G) as far as
possible into the groove in the axle (3).
●
Remove the basic unit from the
cardboard insert.
●
Raise the basic unit into the working
position.
7. Preparing the machine for
operation
Risk of injury:
Carefully read the section entitled
"For your safety" (
Ö
4.) and follow
all the safety instructions before
assembling the garden shredder.
Strictly observe all torques in the
"Preparing the machine for
operation" (
Ö
7.) section to avoid
damaging the machine.
In particular, gloves
should be worn and
contact with the blades
must be avoided.
Avoid damage to the machine.
Place cardboard underneath the
machine to protect it from being
scratched.
Risk of injury:
Lift the machine only with the help
of a second person. Make sure that
the cardboard insert (1) is not
damaged.
3
Risk of injury:
The blade cover must be attached
to prevent any injuries from the
sharp blades. (
Ö
7.4)
Attach both wheel carriers to the
basic unit in such a way that the
bores for the axle are located at the
rear (on the tool box side).
4
Risk of injury:
After installing, check that both feet
are seated securely.
Mount the wheels so that the valves
are located on the outside.
In order to prevent the wheel from
becoming loose when installing,
ensure that retaining ring (G)
engages correctly in the groove (1)
in axle (H).