Viking GB 460, Instruction Manual

Page: 55 / 656

53
DE
FR
NL
IT
ES
PT
NO
SV
FI
DA
PL
SK
HU
HR
EN
0478 216 9905 A - EN
For safety reasons, do not exceed the
following angles of inclination when
transporting and loading the machine:-
–
1
0° (
1
7.6%)
angle of lateral inclination,
–
1
0° (
1
7.6%)
angle of longitudinal
inclination,
Secure the machine and other machine
parts being transported (e.g. on the load
floor using fastening materials (straps,
ropes etc.) of an adequate size at the
fastening points described in this
instruction manual. (
Ö
13.)
Push or pull the machine at walking pace
only. Do not tow!
When transporting the machine, always
observe regional legislation, especially
regarding load security and the transport
of objects on load floors.
4.5 Before operation
Make sure that only persons who are
familiar with the instruction manual are
permitted to use the machine.
Observe the local regulations regarding
permitted operating times for gardening
power tools with combustion engines or
electric motors.
Check the fuel system (particularly visible
parts such as e.g. tank, tank cap, hose
connections) before operating the
machine. In the event of any leaks or
damage, do not start the engine –
Fire
hazard!
Have the machine repaired by a specialist
dealer prior to operation.
Defective mufflers and all other worn or
damaged parts must be removed before
use of the machine. Replace any illegible
or damaged danger signs and warnings on
the machine. Your VIKING specialist has a
supply of replacement stickers and all the
other spare parts.
Before initial operation, it must be ensured
– that the covers and guards are in place
and in good condition
– that all fuel-carrying components are
fitted to the engine and are in good
condition (leak-tight)
– that the tank is in good condition (leak-
tight)
– that the housing and cutting tools
(blades, blade shaft, blade discs, etc.)
are not worn or damaged
– that there is no shredding material in
the machine and that the feed chute is
empty
– that all screws, bolts, nuts and other
fastening elements are in place and
properly tightened. Tighten any loose
screws, bolts and nuts prior to initial
operation (observe tightening torques).
Only use the machine out-of-doors and not
close to walls or any other solid objects in
order to prevent the risk of injuries and
property damage (no escape for the user,
broken windows, scratched cars etc.).
The machine must placed in a stable
position on firm and level ground.
Do not use the machine on a paved or
gravel-covered surfaces, as ejected or
thrown-up material could cause injuries.
Before using the machine, always check
that it is properly closed. (
Ö
7.5)
Make sure that you are familiar with the
On / Off switch so that you can react
quickly and correctly in any emergency
situation.
When the garden shredder is in the
working position, the feed opening must
always be completely covered by the
splash guard. If this is not the case, the
splash guard must be replaced.
Risk of injury:
Only operate the machine when properly
assembled. If parts of the machine
(e.g. wheels, feet etc.), are missing, the
specified safety distances are no longer
maintained and the stability of the machine
may also be reduced.
Before using the machine, always carry
out a visual check to ensure that it is in
good operating condition.
"Good operating condition" means that the
machine is fully assembled, in particular:
– Upper chute is installed on lower chute
– Branch guide is installed
– Feed chute is installed on the basic
machine
– Wheel carrier assembly is installed
– Both wheels are mounted and the tyre
pressure complies with the
specifications contained in this
instruction manual (
Ö
12.12)
– All safety devices (ejection chute,
splash guard etc.) must be present and
functional
– Both cutting units (blade discs) are
installed
– All blades are properly installed
The switch and safety devices installed in
the machine must not be removed or
bypassed.
Visually inspect both blade discs for
damage and deformation; replace if
necessary.