VESPA GTV 125 Page 186 Service Station Manual Download

Page: 186 / 278

- Remove the steering tube

- Use a special tool remove the upper disk of the

fifth wheel fitting seat on the headstock by operat-

ing form the lower part of the headstock as indica-

ted in the photograph. Afterwards remove the

lower disk of the fifth wheel operating from the up-

per part

Specific tooling

020004Y

Punch for removing fifth wheels from

headstock

- Remove the fifth wheel fitting and the dust guard

on the steering tube as shown in figure, using the

specific tool. Proceed giving a few taps with the

mallet.

Specific tooling

020004Y

Punch for removing fifth wheels from

headstock

- Refit the fifth wheel fitting and the dust guard on

the steering tube until they stop, using the specific

tool.

Specific tooling

006029Y

Punch for fitting fifth wheel seat on

steering tube

- Use the specific tool to fit the fifth wheel fitting on

the headstock as indicated in the figure

Specific tooling

020037Y

Punch

Suspensions

Vespa GTV 125

SUSP - 10

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands