VESPA GTV 125 Service Station Manual Download

Page: 103 / 278

Removing the driven pulley

- Remove the spacer, the clutch bell and the whole

driven pulley unit.

N.B.

THE UNIT CAN ALSO BE REMOVED WITH THE
DRIVING PULLEY MOUNTED.

Inspecting the clutch drum

- Check that the clutch bell is not worn or damaged.

- Measure the clutch bell inside diameter.

Characteristic

Max. value clutch bell

Max. value: Ø 134.5 mm

Clutch bell standard value

Standard value: Ø 134 - 134.2 mm

Checking the bell working surface eccentricity

- Install the bell on a driven pulley shaft using 2

bearings (inner diameter 15 and 17 mm).

- Lock with the original spacer and nut.

- Place the bell/shaft assembly on the support to

check the crankshaft alignment.

- Using a feeler pin gauge and the magnetic base,

measure the bell eccentricity.

- Repeat the measurement in 3 positions (Central,

internal, external).

- If faults are found, replace the bell.

Specific tooling

020074Y

Support base for checking crankshaft

alignment

020335Y

Magnetic support for dial gauge

Vespa GTV 125

Engine

ENG - 5

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands