VESPA GTV 125 Service Station Manual Download

Page: 118 / 278

Refitting the wheel axle bearing

Support the hub cover on a wooden surface.

- Heat the cover crankcase with special heat gun.

- Fit the wheel shaft bearing with a modular punch

as shown in the figure.

Specific tooling

020150Y

Air heater support

020151Y

Air heater

020376Y

Adaptor handle

020360Y

Adaptor 52 x 55 mm

020483Y

30 mm guide

Assemble the seeger ring.

- Fit the oil guard with seal lip towards the inside

of the hub and place it flush with the internal sur-

face by means of the appropriate tool used from

the 52 mm side

The 52 mm side of the adapter must be turned to-

wards the bearing.

Engine

Vespa GTV 125

ENG - 20

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands