VESPA GTV 125 Service Station Manual Download

Page: 115 / 278

Removing the hub cover

- Empty the rear hub through the oil drainage plug.

- Remove the 7 flanged screws indicated in the

figure.

- Remove the hub cover and its gasket.

Removing the wheel axle

- Remove the wheel axis complete with gear.

- Remove the intermediate gear.

Removing the hub bearings

- Check the state of the bearings being examined

(wear, clearance and noisiness). If faults are de-

tected, do the following.

- Use the specific bearing extractor to remove the

three 15 mm bearings (2 in the crankcase and 1 in

the hub cover).

Specific tooling

001467Y013

Pliers to extract ø 15-mm bearings

Vespa GTV 125

Engine

ENG - 17

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands