manualshive.com logo in svg

VESPA GTV 125, Service Station Manual

The VESPA GTV 125 is a stylish and reliable scooter that combines classic design with modern technology. To ensure its optimal performance, it is essential to have the Service Station Manual at your disposal. You can easily download this comprehensive manual for free, from our website, manualshive.com, and maintain your Vespa with confidence.

Share
Download
background image

Crankshaft oil seals

Refitting

- Fit the internal bulkhead by locking the two

screws to the prescribed torque.

- Fit the oil filter fitting and tighten it to the specified

torque.

- Place a new gasket on one of the crankcase

halves, preferably on the transmission side, to-

gether with the locating dowels.

- Lubricate the main bushings and insert the crank-

shaft in the transmission side crankcase half.

- Reassemble the two crankcase halves.

- Fit the 11 screws and tighten them to the pre-

scribed torque.

- Lubricate the flywheel oil seal.

- Using the appropriate tool, assemble the oil seal.

- Fit a new O-ring on the pre-filter and lubricate it.

- Insert the filter on the engine with the relative cap.

Tighten to the specified torque.

N.B.

FAILURE TO USE THE SPECIFIC TOOL CAN
RESULT IN AN INCORRECT DEPTH POSITION
AND AS A CONSEQUENCE IN INADEQUATE
OIL SEALING.

Specific tooling

020425Y

 

Punch for flywheel-side oil seal

Locking torques (N*m)

Internal engine crankcase bulkhead (transmis-
sion-side half shaft) screws

 

4 ÷ 6

 

Oil filter on

crankcase fitting

 

27 ÷ 33

 

Engine-crankcase

coupling screws

 

11 ÷ 13

 

Engine oil drainage

plug/mesh filter

 

24 ÷ 30

Engine

Vespa GTV 125

ENG - 60

Summary of Contents for GTV 125























































































































































































































































































Reviews:

No comments

Related manuals for GTV 125

Smart Wheel SMARTkick X7 8.5" User Manual preview
SMARTkick X7 8.5"
Brand: Smart Wheel Pages: 10
Speedlion 84040 User Manual preview
84040
Brand: Speedlion Pages: 9
EMG VELOCIPTOR EVO ES 88E User Manual preview
VELOCIPTOR EVO ES 88E
Brand: EMG Pages: 36
Moma self-balance User Manual preview
self-balance
Brand: Moma Pages: 11
Hudora 14240 Instructions On Assembly And Use preview
14240
Brand: Hudora Pages: 8
Zipr zip'r xtra Owner'S Operating Manual preview
zip'r xtra
Brand: Zipr Pages: 13
TilGreen TilRoue Instructions For Use Manual preview
TilRoue
Brand: TilGreen Pages: 22
Manhattan 200L User Manual preview
200L
Brand: Manhattan Pages: 16
M SCOOTER S1 Original Instruction User Manual preview
S1
Brand: M SCOOTER Pages: 38
prime3 EES21 Owner'S Manual preview
EES21
Brand: prime3 Pages: 24
Sachs Speedforce 50 Service Manual preview
Speedforce 50
Brand: Sachs Pages: 56
ScooterWorks Prima BBQ Rear Rack Instructions preview
Prima BBQ Rear Rack
Brand: ScooterWorks Pages: 5
SCOOT AND RIDE HIGHWAYKICK 5 Instruction Manual preview
HIGHWAYKICK 5
Brand: SCOOT AND RIDE Pages: 22
SCOOTDAWG GY6 Owner'S Manual preview
GY6
Brand: SCOOTDAWG Pages: 26
TN’G L'S Owner'S Manual preview
L'S
Brand: TN’G Pages: 35
Daymak C5 Blast Go Kart User Manual preview
C5 Blast Go Kart
Brand: Daymak Pages: 16
Jetson Hex Kick Scooter Manual preview
Hex Kick Scooter
Brand: Jetson Pages: 23
HURTLE HURTUN 27 User Manual preview
HURTUN 27
Brand: HURTLE Pages: 6

Brands by name

Popular brands

Load more brands