manualshive.com logo in svg

VESPA GTV 125, Service Station Manual

The VESPA GTV 125 is a stylish and reliable scooter that combines classic design with modern technology. To ensure its optimal performance, it is essential to have the Service Station Manual at your disposal. You can easily download this comprehensive manual for free, from our website, manualshive.com, and maintain your Vespa with confidence.

Share
Download
background image

020329Y

 

MityVac vacuum-operated pump

Fuel supply

- To clean the filtering element proceed as follows:

remove the 4 filter cover fixing screws indicated in

the figure; remove the cover and take out the pa-

per filtering element, clean with compressed air

and refit.

- Make sure the filtering element is in the correct

position.

- Check that the air passage sections are not dam-

aged or deformed.

- Check the correct sealing of the coupling be-

tween the filter housing and the cover.

N.B.

FAILURE TO OBSERVE THESE INSTRUC-
TIONS MAY RESULT IN WRONG VACUUM IN-
SIDE THE FILTER HOUSING, WHICH IN TURN
MAY PRODUCE VARIATIONS IN CARBURET-
ION.

Removing the carburettor

Kehin

- To detach the carburettor from the engine, it is

necessary to move the air filter and remove the

transmission throttle control, the automatic starter

connection, the clamps anchoring the carburettor

to the filter housing and to the inlet manifold, the

air delivery pipe to the diaphragm, and the intake

fitting.

- Take out the carburettor and rotate it so as to

remove the screw with the water joint and the

pipes.

N.B.

THIS LAST OPERATION IS NECESSARY SO
AS NO TO EMPTY THE COOLING SYSTEM.

Vespa GTV 125

Engine

ENG - 65

Summary of Contents for GTV 125























































































































































































































































































Reviews:

No comments

Related manuals for GTV 125

Heartway Medical Products S12X Manual preview
S12X
Brand: Heartway Medical Products Pages: 33
Shoprider TE-779XLS User Manual preview
TE-779XLS
Brand: Shoprider Pages: 14
Razor Graffiti Owner'S Manual preview
Graffiti
Brand: Razor Pages: 8
Add Freedom Scooters Foxx ES008 J-4 Operation Manual preview
Foxx ES008 J-4
Brand: Add Freedom Scooters Pages: 19
Zero Motorcycles S 2010 Owner'S Manual preview
S 2010
Brand: Zero Motorcycles Pages: 118
Huffy Tilt N Turn Owner'S Manual preview
Tilt N Turn
Brand: Huffy Pages: 20
Huffy In-Line Owner'S Manual preview
In-Line
Brand: Huffy Pages: 20
Polaris PES 0504 Manual Instruction / Warranty preview
PES 0504
Brand: Polaris Pages: 34
Bigfoot GO-PED Instruction Manual & Parts List preview
GO-PED
Brand: Bigfoot Pages: 4
Yamaha YQ50/YQ50L Owner'S Manual preview
YQ50/YQ50L
Brand: Yamaha Pages: 84
Magnum Cosmo S Manual preview
Cosmo S
Brand: Magnum Pages: 24
Magnum Cosmo+ Manual preview
Cosmo+
Brand: Magnum Pages: 24
Luoov Electric skateboard User Manual preview
Electric skateboard
Brand: Luoov Pages: 24
Razor John Radtke Phase Two Dirt Scoot Diamond... Owner'S Manual preview
John Radtke Phase Two Dirt Scoot Diamond...
Brand: Razor Pages: 5
W-Tec Dalfin User Manual preview
Dalfin
Brand: W-Tec Pages: 14
Mega MULTITRUCK 400 - 600 Manual preview
MULTITRUCK 400 - 600
Brand: Mega Pages: 46
Sym Jet Euro X 50 Manual preview
Jet Euro X 50
Brand: Sym Pages: 31
Sym HD 200 EVO Owner'S Manual preview
HD 200 EVO
Brand: Sym Pages: 32

Brands by name

Popular brands

Load more brands