VESPA GTV 125 Page 110 Service Station Manual Download

Page: 110 / 278

- Loosen the tool clamp and insert the belt accord-

ing to its direction of rotation.

- Lock the driven pulley again using the specific

tool.

- Preload the clutch return spring with a traction/

rotation combined action until it reaches the pul-

leys maximum opening and place the belt on the

minimum rolling diameter.

- Remove the driven pulley /belt assembly from the

tool.

N.B.

FOR DESIGN REASONS, THE NUT IS SLIGHT-
LY ASYMMETRIC; THE FLATTEST SURFACE
SHOULD BE MOUNTED IN CONTACT WITH
THE CLUTCH.

N.B.

DURING THE SPRING PRELOADING PHASE,
BE CAREFUL NOT TO DAMAGE THE PLASTIC
SPRING STOP AND THE BUSHING THREAD-
ING.

N.B.

AN EXCESSIVE QUANTITY CAN DAMAGE THE
CLUTCH OPERATION.

Specific tooling

020444Y011

adapter ring

020444Y009

46x55 Wrench

Locking torques (N*m)

Clutch unit nut on driven pulley

55 ÷ 60

Refitting the driven pulley

- Reassemble the clutch bell and spacer.

Engine

Vespa GTV 125

ENG - 12

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands