VESPA GTV 125 Service Station Manual Download

Page: 138 / 278

Inspecting the timing system components

- Check that the guide shoe and the tensioner shoe

are not worn out.

- Ensure that the camshaft control pulley chain as-

sembly and the sprocket wheel are not worn.

- If you encounter wear, replace the parts or, if the

chain, sprocket wheel and pulley are worn replace

the whole assembly.

- Remove the centre screw with the washer and

the tensioner spring. Check that the one-way

mechanism is not worn.

- Check the condition of the tensioner spring.

- If examples of wear are found, replace the whole

assembly.

Inspecting the valve sealings

- Insert the valves into the cylinder head.

- Alternatively check the intake and exhaust

valves.

- The test is carried out by filling the manifold with

petrol and checking that the head does not ooze

through the valves when these are just pressed

with the fingers.

Engine

Vespa GTV 125

ENG - 40

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands