VESPA GTV 125 Service Station Manual Download | Manualshive

Page: 45 / 278

background image

- Dry with short blasts of compressed air and a clean cloth.

- Soak with a 50% mixture of gasoline and oil.

- Drip dry the filtering element and then squeeze it with your hands without wringing.

- Refit the filtering element.

CAUTION

NEVER RUN THE ENGINE WITHOUT THE AIR FILTER, THIS WILL RESULT IN AN EXCESSIVE
CYLINDER AND PISTON WEAR AND ALSO IN CARBURETTOR DAMAGE.

CAUTION

WHEN TRAVELLING ON DUSTY ROADS, THE AIR FILTER MUST BE CLEANED MORE OFTEN
THAN SHOWN IN THE SCHEDULED MAINTENANCE CHART.

Recommended products

AGIP FILTER OIL

Oil for air filter sponge

Mineral oil with specific additives for increased adhesiveness

- Remove the left side panel.

- Remove the air cleaner cover after unscrewing

the 9 fixing screws.

- Take out the filtering element.

- Replace the air filter with a new one.

N.B.

EVERY 6,000 KM CHECK THE AIR FILTER AND
IF REQUIRED, CLEAN IT WITH COMPRESSED
AIR. THE AIR JET MUST BE DIRECTED FROM
THE INSIDE TO THE OUTSIDE OF THE FILTER
(I.E. OPPOSITE TO THE SENSE THE AIR
FLOWS AT REGULAR ENGINE RUNNING). EV-
ERY 6,000 KM, UPON SERVICING, REMOVE
THE RETAINER AND RUBBER COVER UNDER
THE FILTER HOUSING AS SHOWN IN THE FIG-
URE AND DRAIN ALL POSSIBLE OIL DEPOS-
ITS.

Vespa GTV 125

Maintenance

MAIN - 11

«
...
43
44
45
46
47
...
»

Summary of Contents for GTV 125























































































































































































































































































Reviews:

No comments

Related manuals for GTV 125

Brand: Days Pages: 94

Brand: Razor Pages: 6

Fortress 2000 SERIES

Brand: Handicare Pages: 21

Brand: Robogo Pages: 15

Brand: Local Motors Pages: 41

Brand: Dynacraft Pages: 27

Brand: Nipponia Pages: 38

Brand: Nipponia Pages: 54

Brand: Hama Pages: 64

XL MAX LITE SC6000

Brand: Youin Pages: 80

Brand: wayscral Pages: 269

Brand: Yamaha Pages: 64

Brand: Kayoba Pages: 12

Brand: Shoprider Pages: 19

Brand: Meteor Pages: 8

Steering Grip Kit

Brand: Segway Pages: 2

Brand: UrbMob Pages: 8

Brand: Thunder Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands