VESPA GTV 125 Service Station Manual Download Page 122

Page: 122 / 278

Refitting the stator

- Refit the stator and flywheel carrying out the re-

moval procedure in reverse, tightening the retain-

ers to the prescribed torque.

- Place the cable harness as shown in the figure.

- Stator screws and Pick-Up

N.B.

THE PICK-UP WIRE SHOULD BE POSITIONED
BETWEEN THE UPPER SCREW AND THE REF-
ERENCE PIN AS SHOWN IN THE DETAIL
DRAWING.

Locking torques (N*m)

Stator assembly screws (°)

3 ÷ 4

Refitting the flywheel cover

- Place the flywheel with the top dead centre mark

aligned with the crankcase.

- Place the flywheel cover by aligning the reference

marks of the drive and the crankcase cover.

- Reassemble the cover on the engine, placing the

three connectors in the drive for the water pump.

- Carry out the steps in the reverse order from the

dismantling procedure.

CAUTION

TAKE CARE TO CORRECTLY POSITION THE
FLYWHEEL CONNECTOR. MAKE SURE THE
CENTRING DOWELS ARE PRESENT.

Flywheel and starting

- Check the integrity of the internal plastic parts of the flywheel and the Pick-Up control plate.

Engine

Vespa GTV 125

ENG - 24

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Brands by name

Popular brands