VESPA GTV 125 Service Station Manual Download

Page: 92 / 278

This section describes the operations to carry out when removing the engine from the vehicle.

Exhaust assy. Removal

- Undo the two exhaust manifold fixings on the

head.

- Undo the three screws fixing the muffler to the

support arm.

Remove the full muffler unit.

Removal of the engine from the vehicle

-Carry out the removal operations but in reverse order and respect the locking torques indicated in the

Characteristics Chapter.

Check that there is a small clearance when the valve is in abutment against the set screw.

-Check the engine oil level and if necessary top it up with the recommended type.

- Top-up the cooling circuit.

- Check the functioning of the accelerator and the electrical devices.

CAUTION

PAY PARTICULAR ATTENTION TO POSITIONING THE THROTTLE COMMAND TRANSMISSION
PROPERLY.

Engine from vehicle

Vespa GTV 125

ENG VE - 2

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands