manualshive.com logo in svg

VESPA GTV 125, Service Station Manual

The VESPA GTV 125 is a stylish and reliable scooter that combines classic design with modern technology. To ensure its optimal performance, it is essential to have the Service Station Manual at your disposal. You can easily download this comprehensive manual for free, from our website, manualshive.com, and maintain your Vespa with confidence.

Share
Download
background image

If no voltage is detected, check the cable harness, the connections and make sure the 15A main fuse

is in good conditions; otherwise, proceed as follows:

- Jump terminals No.1 (Black/Blue) and No. 4 (Red/Black) (see figure), and set the turn indicator switch

alternately to the left and to the right and check that the lights turn on.

If they do, replace the control unit because it is faulty.

If they do not turn on, check the control unit-turn indicator switch connection cable harness; then, repeat

the test.

If the cable harness is in good conditions and the turn indicators still do not turn on, replace the turn

indicator switch because it is faulty.

Vespa GTV 125

Electrical system

ELE SYS - 19

Summary of Contents for GTV 125























































































































































































































































































Reviews:

No comments

Related manuals for GTV 125

e-way E-600 User Manual preview
E-600
Brand: e-way Pages: 156
DAELIM S2 125 Owner'S Manual preview
S2 125
Brand: DAELIM Pages: 66
DAELIM S-FIVE - Manual preview
S-FIVE -
Brand: DAELIM Pages: 66
DAELIM S-FIVE - Specification preview
S-FIVE -
Brand: DAELIM Pages: 2
DAELIM Q2 Owner'S Manual preview
Q2
Brand: DAELIM Pages: 92
DAELIM LIBERTY Owner'S Manual preview
LIBERTY
Brand: DAELIM Pages: 34
DAELIM DELFINO Owner'S Manual preview
DELFINO
Brand: DAELIM Pages: 62
Excell Excite 3 Galaxy User Manual preview
Excite 3 Galaxy
Brand: Excell Pages: 27
NAVEE S65C User Manual preview
S65C
Brand: NAVEE Pages: 44
Xiaomi Mi M365 User Manual preview
Mi M365
Brand: Xiaomi Pages: 12
ROOES SMARTE-SCOOTER Manual preview
SMARTE-SCOOTER
Brand: ROOES Pages: 12
Razor 100 Reference Manual preview
100
Brand: Razor Pages: 12
Lehe L1 series Manual preview
L1 series
Brand: Lehe Pages: 13
Quantum TRU-BALANCE 3 Basic Operation Instructions preview
TRU-BALANCE 3
Brand: Quantum Pages: 28
JD Bug XF-136 Cool Carver Owner'S Manual preview
XF-136 Cool Carver
Brand: JD Bug Pages: 6
DARTY STREET MOTION User Manual preview
STREET MOTION
Brand: DARTY Pages: 12
Zipr Mantis PC Owner'S Manual preview
Mantis PC
Brand: Zipr Pages: 25
Olsson and Brothers E-SCOOTER User'S Manual And Garantee preview
E-SCOOTER
Brand: Olsson and Brothers Pages: 68

Brands by name

Popular brands

Load more brands