VESPA GTV 125 Service Station Manual Download

Page: 180 / 278

Soap-based lithium grease with NLGI 3; ISO-L-

XBCHA3, DIN K3K-20

Refitting the front wheel

- To refit, carry out the removal operations but in reverse order and comply with the specified locking

torque.

Locking torques (N*m)

Wheel fixing screw

20 ÷ 25

Steering column

Removal

- Remove the front wheel

- Remove the brake calliper

- Loosen the screw fixing the odometer cable plate

and take out the cable.

- Remove the suspension arm housing by un-

screwing the three screws indicated in the photo-

graph.

Suspensions

Vespa GTV 125

SUSP - 4

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands