background image

This section è is devoted to the operations that can be carried out on the vehicle's bodywork.

Seat

Saddles fitted to this scooter are upholstered in Authentic Leather, and are a stylish accessory to em-

phasise an already exclusive product such as your Vespa. As leather is a natural and vivid material, it

tends to get "very opaque" aspect as time goes by, an aspect typical of Authentic Leather. This product

may also show characteristic undertones and strains.

To care and maintain the features of the saddle through time, follow these tips: Do not expose it to

weather changes, when the scooter is parked protect it with the waterproof cover supplied and stored

under the saddle.

Periodically, especially during rainy seasons, apply commercially available waterproofing products

(footwear spray). Do not apply shoe polish or wax on the saddle so as not to stain your clothes.

In case of forced and prolonged exposure to water, dry the saddle far from any heat source, do not to

use alcohol, solvent-based products and pay special care when refuelling.

If the saddle gets stained, wipe the area and if necessary wash it with lukewarm water and neutral soap.

- Remove the helmet compartment

- Remove the two screws shown in the photograph

- Remove the saddle

Chassis

Vespa GTV 125

CHAS - 2

Summary of Contents for GTV 125























































































































































































































































































Reviews: