VESPA GTV 125 Page 175 Service Station Manual Download

Page: 175 / 278

Kehin

- Check that the automatic starter piston is not de-

formed or rusty.

- Check that the piston slides freely from the seat

to the support.

- Check that the piston sealing gasket is not de-

formed.

- The starter must be more or less functional de-

pending on the ambient temperature.

- Measure the protrusion of the piston as shown in

the figure and check its corresponding value.

- Make sure that the starter is adjusted for the am-

bient temperature.

- The starter should disconnect progressively by

means of electrical heating.

- Check the starter resistance when adjusted to the

ambient temperature.

With a 12V battery power the automatic starter and

check that the piston protrudes as much as possi-

ble.

- The correct warm up time depends on the ambi-

ent temperature.

- If protrusion, resistance or timing values are dif-

ferent from the ones prescribed, replace the start-

er.

- Assemble the starter to the carburettor being

careful to position the O-Ring correctly, insert the

plate with the machined side contacting the starter,

tighten the fixing screws.

- Position the starter as shown in the figure.

- Assemble the protection casing.

N.B.

TO CARRY OUT THIS CHECK PAY SPECIAL
ATTENTION NOT TO GENERATE SHORT CIR-
CUITS USE A CABLE SECTION WITH A TER-
MINAL SUITABLE TO BE CONNECTED TO THE
STARTER.

Characteristic

Starter pin travel

Vespa GTV 125

Engine

ENG - 77

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands