manualshive.com logo in svg

VESPA GTV 125, Service Station Manual

The VESPA GTV 125 is a stylish and reliable scooter that combines classic design with modern technology. To ensure its optimal performance, it is essential to have the Service Station Manual at your disposal. You can easily download this comprehensive manual for free, from our website, manualshive.com, and maintain your Vespa with confidence.

Share
Download
background image

Oil pressure check

- After removing the flywheel cover as described

in the "Flywheel" chapter, remove the electrical

connexion of the minimum oil pressure switch and

then remove the switch.

- With the engine idling at 1650 rpm and the oil

temperature at ~90°C, check that the oil pressure

is between 0.5 ÷ 1.2 atm.

- With the engine idling at 6000 rpm and the oil

temperature at ~90°C, check that the oil pressure

is between 3.2 ÷ 4.2 atm.

- Remove the appropriate tools once the meas-

urement is complete, refit the oil pressure switch

and washer, tightening it to the specified torque

and fit the fan cover.

- If the oil pressure is outside the specified limits,

in the following order, check: the oil filter, the oil

by-pass valve, the oil pump and the crankshaft

seals.

N.B.

THE CHECK MUST BE CARRIED OUT WITH
OIL AT THE CORRECT LEVEL AND WITH AN
OIL FILTER IN GOOD CONDITION.

Characteristic

Oil pressure

Minimum pressure admitted at 6000 rpm: 3.2 atm.

Locking torques (N*m)

Minimum oil pressure sensor

 

12 ÷ 14

Vespa GTV 125

Engine

ENG - 59

Summary of Contents for GTV 125























































































































































































































































































Reviews:

No comments

Related manuals for GTV 125

Zero 2014 FX Owner'S Manual preview
2014 FX
Brand: Zero Pages: 126
Coccolle Muvio User Manual preview
Muvio
Brand: Coccolle Pages: 12
Kogan FORTIS FS27HCMEBKA User Manual preview
FORTIS FS27HCMEBKA
Brand: Kogan Pages: 20
King Song N1-A User Manual preview
N1-A
Brand: King Song Pages: 48
Kangaroo Golf Z 2020 Series Quick Start Manual preview
Z 2020 Series
Brand: Kangaroo Golf Pages: 7
Razor kuties Owner'S Manual preview
kuties
Brand: Razor Pages: 8
Qlink Achille 150 User Manual preview
Achille 150
Brand: Qlink Pages: 37
Rehasys GATSBY User Manual preview
GATSBY
Brand: Rehasys Pages: 46
Baotian BT125T-2 Service Manual preview
BT125T-2
Brand: Baotian Pages: 29
KOMFI-RIDER Liberty User Manual preview
Liberty
Brand: KOMFI-RIDER Pages: 28
Roma Medical S-889XLSBN User Manual preview
S-889XLSBN
Brand: Roma Medical Pages: 20
SILENCE S02 LS User Manual preview
S02 LS
Brand: SILENCE Pages: 62
Razor Trikke Owner'S Manual preview
Trikke
Brand: Razor Pages: 16
Razor RSF350 Owner'S Manual preview
RSF350
Brand: Razor Pages: 16
Razor RipStik Electric Quick Start Manual preview
RipStik Electric
Brand: Razor Pages: 28
Razor Rift Manual preview
Rift
Brand: Razor Pages: 28
Zinc FOLDING ELECTRIC SWIFT PLUS SCOOTER Owner'S Manual preview
FOLDING ELECTRIC SWIFT PLUS SCOOTER
Brand: Zinc Pages: 11
Benelli Velvet Owner'S Manual preview
Velvet
Brand: Benelli Pages: 178

Brands by name

Popular brands

Load more brands