VESPA GTV 125 Page 172 Service Station Manual Download

Page: 172 / 278

- Wash and blow the flow screw properly.

- Check that screw is not deformed and/or rusty.

- Assemble the spring on the screw.

- Screw the flow screw on the carburettor body.

- The screw final position should be determined by an exhaust fume analysis.

- Adjust the carburettor by turning the screw twice from the close position.

Level check

Kehin

- Place the carburettor inclined as shown in the

figure.

- Check that the float reference is parallel to the tank coupling surface

- If different positions are detected, change the plunger control metal plate direction to obtain the position

described above.

Inspecting the valve and needle

Engine

Vespa GTV 125

ENG - 74

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands