VESPA GTV 125 Service Station Manual Download

Page: 106 / 278

Specific tooling

001467Y035

Belle for OD 47-mm bearings

- Remove the roller bearing using the modular

punch.

Specific tooling

020376Y

Adaptor handle

020456Y

Ø 24 mm adaptor

020363Y

20 mm guide

Inspecting the driven fixed half-pulley

- Measure the outer diameter of the pulley bushing.

- Check the contact surface with the belt to make

sure there are no flaws.

Characteristic

Half-pulley standard diameter

Standard diameter: Ø 40.985 mm

Half-pulley minimum diameter

Minimum admissible diameter Ø 40.96 mm

Inspecting the driven sliding half-pulley

- Remove the two internal grommets and the two

O-rings.

- Measure the movable half-pulley bushing inside

diameter.

Characteristic

Movable driven half-pulley max. diameter

Max. diameter admitted: Ø 41.08 mm

Movable driven half-pulley standard diameter

Standard diameter: Ø 41.000 ÷ 41.035 mm

Engine

Vespa GTV 125

ENG - 8

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands