VESPA GTV 125 Service Station Manual Download

Page: 220 / 278

Check

1) Look to see that the thermostat is not damaged.

2) Fill a metal container with approx. 1 litre of wa-

ter.

Immerse the thermostat, and keep it in the centre

of the container.

Immerse the multimeter temperature probe, and

keep it close to the thermostat.

Heat up the container using the thermal gun.

Check the temperature when the thermostat starts

to open:

Heat up until the thermostat is completely open.

3) Replace the thermostat if it is not working prop-

erly.

CAUTION

TO EXECUTE THE TEST CORRECTLY, MAKE
SURE NEITHER THE THERMOSTAT NOR THE
THERMOMETER TOUCHES THE CONTAINER.

Specific tooling

020331Y

Digital multimeter

020151Y

Air heater

Characteristic

Thermostat check: Opening start temperature

69.5 ÷ 72.5°C

Cooling system

Vespa GTV 125

COOL SYS - 6

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands