manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 88

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Preparing the Equipment Baler 7-25

Figure 48. C

Figure 49. D

•

At start of wrap cycle

•

Tractor hydraulic valve operating tailgate circuit must be in float position to allow cylinder (4) to retract.

•

A solenoid valve opens when wrap cycle begins. This allows cylinder (4) to retract by means of spring pressure, moving roller (3) rearward.
(see page 7-25)

•

Roller (3) begins rotating when netwrap feed clutch engages.

NOTICE

If tractor hydraulic valve operating tailgate circuit is not in float position, cylinder (4) may not be able to retract and
netwrap (2) will feed into rotor (5) as shown in left illustration.

•

In rearward position, roller (3) directs netwrap (2) to roller (1) and onto bale.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands