Vermeer 504 PRO Operator And Maintenance Manual Download Page 24

Page: 24 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

Safety Messages 2-11

The accumulator is under gas and oil pressure. Depressurize hydraulic system prior to disassembling or repair.

Stepping or standing on some areas of machine may result in slipping or falling. Do not step on prohibited
areas.

DANGER:

Entanglement in rotating driveline can result

in death or serious injury.

Stay away from rotating driveline. Stop engine and ensure PTO driveline is stopped before working on driveline.

Keep driveline shields in place at all times. Ensure shields turn and telescope freely.

Wear Close-fitting clothing and confine long hair

2.4

Personal Protective Equipment

Wear required personal protective equipment. Wear close-fitting clothing and confine long hair. Avoid wearing jewellery such as rings,
wristwatches, necklaces or bracelets. Always wear: safety glasses and safety shoes.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands

Vermeer 504 PRO, Operator And Maintenance Manual

Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands