manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 87

504PRO_604PRO_o-m2_00

-

7-24 Preparing the Equipment Baler

504/604 PRO Baler

When netwrap roller valve (6)(see page 7-23) is turned to the operating position, netwrap roller (3) performs the following functions:

•

During wrap cycle

•

Roller (3) is in rearward position(see page 7-25).

•

Roller (3) is belt-driven from roller (1) and rotates

counterclockwise (viewed from right) to help feed netwrap onto bale.

•

Roller (3) stops rotating when netwrap feed clutch on right side of roller (1) disengages.

•

During bale ejection

•

Cylinder (4) is connected to tailgate hydraulic circuit and extends to move netwrap roller (3) forward when tailgate raises.(see page 7-25)

•

During bale formation

•

Roller (3) remains in forward position.

•

This lets debris drop between rollers (1) and (3), helping to prevent buildup in front of baler.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands