manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 134

504PRO_604PRO_o-m2_00

-

11-18 Maintenance/Setting

504/604 PRO Baler

At the end of the season annually (in case of special operating conditions also weekly)

17

Star ratchet in pick-up drive

A

left baler side

18

Bearing on pick-up

Applies to camless pickup: left and right grease
nipple can only be seen after removal of the
side covers

A

on both sides

20

Main gear unit

C
2.2 l

Oil change

Check the filling level with a dip stick or overflow hole

11.8.3

Clean the Baler

NOTICE

During the first three months after delivery, do not use a high pressure steam cleaner (the paint still hardens during that
time).

NOTICE

Do not use a steam pressure higher than 100 bar (1450 psi) and water with a temperature higher than 50 ºC.

NOTICE

Keep the nozzle of the steam cleaner at least 7.9

”

(20 cm) from the surface and at an angle (to prevent damage to the

paint).

NOTICE

Do not spray water directly onto the hydraulic system, electrical system or bearings (to prevent damage).

Procedure

1. Make sure the baler is switched off according to the shut down procedure for maintenance or:

1. Make sure the PTO shaft is switched off, tractor engine is stopped and the key is removed.

2. Disconnect the cables of electrical power supply, lighting and control panel.

2. Clean the baler with a high pressure (steam) cleaner. Obey the instructions that are given above.

3. Lubricate all bearings to push out (possible) water.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands