Vermeer 504 PRO Operator And Maintenance Manual Download Page 38

Page: 38 / 153

504PRO_604PRO_o-m2_00

5-2 Controls and Adjustments

504/604 PRO Baler

Figure 10. E-link Pro buttons

Key

A. ON/OFF

Push ON/OFF to switch the monitor On or Off

1. Start

Push Start to start or restart a net wrap cycle

6. Home

Push Home to activate the home page

B. Escape

Push Esc to stop with the Up/Down navigation

2. Manual/Automatic

Push Manual/automatic to switch between the
manual and automatic bale wrap mode.

Bale setup

Push Bale setup to activate the page where
bale settings can be made

C. Up/Down

Push Up or Down to navigate in menus
Push Up or Down to increase or decrease
values

3. Knives

Push Knives to switch the function of the
double acting valve in the tractor to lift/lower
the knives.

8. Statistics

Push Statistics to activate the page where
statistics can be viewed

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands

Vermeer 504 PRO, Operator And Maintenance Manual

Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands