manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 127

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Maintenance/Setting 11-11

11.7

Chain Lubrication System Maintenance

11.7.1

Check the Level in the Oil Container of the Chain Lubrication

The chain lubrication system supplies oil from the container to the drive chains. Check the level in the oil container daily. Do not leak oil.

CAUTION:

Damage to the lubrication pump and roller chains can occur when the system runs without oil. Never let the oil

container run completely empty.

CAUTION:

Damage to the lubrication pump, roller chains and baler when the system runs with the wrong oil flow.Never

change the flow rate of the lubrication pump that was set in the factory. If adjustment is required, only a trained service
technician is allowed to make the change on the basis of the service information provided by Vermeer.

Procedure

1. Make sure the PTO shaft is switched off, tractor engine is stopped and the key is removed.

2. Check the level in the oil reservoir (2) .If necessary fill the oil container.

11.7.2

Fill the Oil Container

Requirements

•

Oil: SAE 30 motor oil or equivalent.

Procedure

1. Make sure the PTO shaft is switched off, tractor engine is stopped and the key is removed.

2. Clean the surroundings of the oil container (2) (see Figure 73 on page 11-12), this prevents that dirt falls in the container when you open it.

3. Remove the container cap (1).

4. Make sure the filter is clean, if necessary:

1. Remove the filter from the oil container.

2. Clean the filter and use exclusively petroleum-benzine or petroleum.

3. Insert the filter in the oil container.

5. Pour the new and clean oil through the filter and fill the oil container up to the marked maximum.

6. Put the container cap on the container.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands