manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 28

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Safety Messages 2-15

•

Depressurize hydraulic system as described in Shutdown procedure (see page 6-1).

•

Secure hydraulic operated parts (pick-up, cutting device) mechanically against unexpected movements.

•

If any

short-time

maintenance or assembly work is carried out with the tailgate open, the tailgate must be hydraulically secured against

lowering: use the shut off valve (on the left side of machine). When the valve is shut off, the actuating lever is perpendicular to the flow
direction.

•

In case of

longer

maintenance or assembly work with the tailgate open, the tailgate must (in addition to the hydraulic safeguard) be

mechanically secured against lowering - using suitable means. This is necessary because, even if the hydraulic system is shut off, hydraulic
pressure losses may still occur.

•

After completion of any maintenance and/or assembly work reset the valve to its initial position and/or remove the mechanical safeguard.

2.7

Safety Devices

2.7.1

Tailgate Safeguard

The tailgate safeguard is a hydraulic shut-off valve that secures an opened tailgate and prevents it from lowering. The shut-off valve is located on
the left side of the maintenance platform. Always set the shut-off valve in the 'shut-off' position (perpendicular to lines) when you do
maintenance with the tailgate open.

Set the tailgate safeguard

1. Open the tailgate.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands